# How to Use a Beverage Dispenser

Set up, fill and pour from a beverage dispenser with confidence, from assembling the spigot and placing it on a level surface to adding soda and cleaning up.

Using a beverage dispenser comes down to three habits: assemble the spigot tightly, set the container on a level surface, and fill it in the right order. A gravity-fed dispenser pours by itself once the tap is open, so the placement and the seal do the work for you. A few checks before the first glass keep the table dry and the drinks flowing. 

- Assemble and tighten the spigot before the dispenser holds any liquid.
- Place the dispenser on a level surface where the tap can open fully.
- Add ice after the liquid, or chill the drink in advance, to keep the mix balanced.
- Open the tap slowly and close it firmly to avoid drips between pours.
- Clean the spigot and container after every use, since residue builds up in the tap.
 

## Know how a gravity dispenser works 

A beverage dispenser is a container with a dispensing tap, also called a spigot, set low on the side. Liquid flows down and out through the tap when you open it, a system known as gravity-fed dispensing. No pump or power is needed, so the drink pours as long as the container sits above the outlet. 

The lid keeps the drink covered and limits spills when the container is moved. Beverage dispensers come in glass, plastic and metal, and the tap may be a simple push button or a lever. The mechanism stays the same across types, which is why the setup steps below apply to each of them. 

Soda behaves differently in a gravity dispenser than in a machine with carbon dioxide. A CO2 soda dispenser mixes syrup, water and gas at the moment of pouring. A gravity container holds a drink that is already mixed, so the carbonation comes from the liquid you pour in. 

## Assemble the spigot before filling 

Dispenser assembly starts with the spigot, and this is the step that prevents leaks. Fit the washer and the tap body into the opening according to the maker's operating instructions. Hand-tighten the nut from the inside of the container, then check that the seal sits flat against the wall. 

A tap that turns too far can crack a plastic wall or crush a gasket. Tighten until the spigot feels firm, then stop. If the parts came loose in the box, lay them out in order before you begin, so no washer is left out. 

Fill the container with plain water and let it stand for a few minutes before the event. A small drip under the tap means the seal is wrong or the nut is loose. Fix that now, while the container is empty and easy to handle. 

## Choose a stable spot on the table 

Placement on a table matters as much as the seal, because a full dispenser is heavy and tips easily. Choose a level surface that holds the weight without flexing. Keep the container back from the table edge, where a sleeve or a plate can knock it. 

Stable placement means the base sits flat with no wobble under it. A folded cloth or a tray under the container catches drips and stops it from sliding. Check the surface with a glass of water first if you are unsure whether the table is level. 

Leave room in front of the tap for a glass and for the hand that holds it. The tap needs to open through its full travel, so nothing should sit against the spout. Tall glasses need clearance above the base, which is why a dispenser with a raised stand helps at a crowded table. 

## Fill the dispenser in the right order 

Filling with ice first and liquid second gives a colder drink but a weaker mix as the ice melts. Pour the chilled drink in first, then add ice to the top if you want it. Either order works, and the choice depends on how strong you want the last glass to be. 

Stop filling below the lid line, since liquid expands and splashes as it is poured. A wide funnel keeps the rim clean when the container is tall. Wipe the outside dry before the guests arrive, so the first hand that touches it stays clean. 

For a mixed drink, stir gently with a long spoon before the first pour. Sugar syrups and juices settle at the bottom, and the tap draws from the lowest point. A quick stir at the start and again halfway through the event keeps each glass consistent. 

## Put soda in a drink dispenser 

You can put soda in a drink dispenser, and a gravity container handles it well as long as you manage the fizz. Pour the soda slowly down the inside wall or over the back of a spoon. A fast pour releases the gas and leaves a flat drink. 

Chill the soda before it goes in, because cold liquid holds carbonation better than warm liquid. Add ice at the last moment, or use a separate ice bucket so the soda is not diluted. Keep the lid on between pours to slow the loss of bubbles. 

Open the tap gently with soda, since a wide-open tap makes foam. Pouring soda into a beverage dispenser that already holds juice creates a mixed drink, and the soda should go in last. A dispenser setup with soda works for a party, but the drink is at its liveliest soon after mixing. 

## Pour from the tap without drips 

Serving drinks cleanly depends on how you work the tap and the glass. Hold the glass close to the spout and tilt it slightly, then open the tap with a steady hand. A glass held far below the spout splashes and foams. 

Close the tap firmly after each pour, and let the last drops fall into the glass rather than onto the table. A small drip tray under the spout catches what remains. Wipe the spout with a clean cloth between servings of different drinks. 

Check the level in the container as the gathering goes on, and refill before it runs dry. A nearly empty dispenser tilts and pours unevenly. Lifting a full container is a two-person job, and the lid should be on before it moves. 

## Clean the dispenser and spigot 

Cleaning starts with the tap, because residue collects inside it and turns sour. Take the spigot apart after each use and wash the parts in warm soapy water. Rinse them well, since soap left in the tap spoils the next drink. 

Wash the container with a soft cloth rather than an abrasive pad, which scratches glass and dulls plastic. Pay attention to the corners and the area around the spigot opening. Let every part air-dry fully before you reassemble the dispenser. 

Sugar-heavy drinks such as soda and juice leave a sticky film that attracts insects. A thorough rinse after the event saves work later. Store the dispenser with the lid off and the tap loose, so air can move through it. 

## Questions about using a beverage dispenser 

### How do drink dispensers work? 

Drink dispensers work by gravity, with liquid flowing down through a tap set low on the container. Opening the tap lets the drink pour, and closing it stops the flow. No power or pump is involved in a gravity-fed dispenser. 

### How do I set up a drink dispenser? 

Setting up a drink dispenser means fitting the spigot with its washer, tightening it by hand, and testing the seal with water. Then place the container on a level surface, fill it, and put the lid on. Check for drips before the first guest arrives. 

### Can you put soda in a drink dispenser? 

Yes, you can put soda in a drink dispenser, and a gravity container holds it well. Pour the soda slowly to keep the bubbles, and chill it first. Add ice at the last moment so the drink stays fizzy. 

### How do I set up a soda dispenser? 

Soda dispenser setup follows the same steps as any gravity dispenser: assemble and test the tap, level the base, and fill with chilled soda. A machine that uses carbon dioxide is different and needs a trained technician to install. 

### What is a spigot on a beverage dispenser? 

A spigot, or dispensing tap, is the valve at the bottom of the container that controls the flow. It holds a washer and a nut that seal it against the wall. A loose or damaged spigot is the source of most leaks.
