How to Make a Tablecloth from Fabric
Learn how to make a tablecloth from fabric: measure your table, choose the drop length, cut the fabric straight, and sew a neat hem for a finished edge.
Contents
- Measure the table before you buy fabric
- Choose the tablecloth drop length
- Pick a fabric that drapes and washes
- Cut the fabric square and straight
- Sew a double-fold hem around the edge
- Finish the corners and press the cloth
- No-sew options for a quick tablecloth
- Tablecloth Questions Answered
- How much fabric do I need for a tablecloth?
- What is the right drop length for a tablecloth?
- Can I make a tablecloth without sewing?
- How do I cut fabric straight for a tablecloth?
- Which fabric works well for a tablecloth?
- Should I prewash fabric before hemming a tablecloth?
You make a tablecloth from fabric by measuring the tabletop, adding the drop you want on each side, cutting the fabric to that size, and sewing a hem around the edge. The drop length you pick sets the finished look and how much fabric you need.
- Measure the tabletop length and width, then add twice your chosen drop to each measurement.
- Decide the drop before you buy fabric, because it sets the size of the cut piece.
- Cut on the straight grain and square the corners so the tablecloth hangs evenly.
- A double-fold hem gives a clean edge and hides the raw fabric inside the fold.
- Press the hem before you sew it, and press it again when the tablecloth is done.
Measure the table before you buy fabric
Measuring for a tablecloth starts with the flat top of the table. Run a tape measure across the length and the width of the tabletop, and write both numbers down.
Round tables need one more number, the diameter across the center of the top. Rectangular and square tables use length and width, and the drop is added to each side.
Measure with the table set up where it will stand, because a leaf or an extension changes the size. Check the numbers twice before you order or cut any fabric.
Choose the tablecloth drop length
Tablecloth drop length means how far the fabric hangs below the table edge, and it changes the whole look of the table. A short drop suits a casual meal, while a longer drop reads as more formal.
The drop runs down all four sides on a rectangular table, so add it twice to the length and twice to the width. One drop on each side gives the total fabric size before hemming.
A very long drop reaches the floor and collects dust and feet, so decide what suits the room. Keep the drop the same on every side so the hem line stays level.
- Short drop: fabric ends just below the table edge
- Medium drop: fabric falls about halfway down the side
- Long drop: fabric reaches close to the floor
- Floor length: fabric touches the floor all around
Pick a fabric that drapes and washes
A fabric tablecloth works when the cloth hangs softly and can be washed after a meal. Look at how the fabric falls from your hand, since a stiff cloth stands away from the table edge.
Natural fibers such as cotton and linen press well and take a crisp hem. Blends can resist wrinkles, and a heavier weave hides the table underneath better than a thin one.
Check the fabric width against your table before you buy, because a wide table may need two lengths joined. Prewash and press the fabric first so the tablecloth does not shrink after the hem is sewn.
Cut the fabric square and straight
Cutting fabric for a table starts with a straight edge, so pull a thread across the width and cut along the line it leaves. A cut that follows the grain keeps the tablecloth from twisting at the corners.
Mark the finished size plus a hem allowance on all four sides, then check the diagonals with a tape. Equal diagonals tell you the piece is square before you cut.
Lay the fabric flat on a large table or the floor and weight the corners. Sharp shears and a long ruler give a straighter line than freehand cutting.
Sew a double-fold hem around the edge
Hemming a tablecloth with a double fold hides the raw edge and gives a sturdy finish that survives washing. Fold the edge under by a small amount, press it, then fold it again by the same amount.
Pin the fold at short intervals and stitch close to the inner fold. A straight stitch works on woven fabric, and a narrow zigzag stitch suits a stretchy cloth.
Miter the corners so the hem folds do not bunch at each point. Trim the excess fabric inside the corner, fold the diagonal, and stitch through all the layers.
Finish the corners and press the cloth
Corner treatment decides whether the tablecloth hangs cleanly or pulls up at the points. A mitered corner folds the two hems into a diagonal seam and lays flat on the table.
Press each seam as you sew, then press the finished tablecloth on the wrong side. Steam helps a cotton or linen cloth relax into a smooth hang.
Check the hem depth all around before the final press, since a fold that wandered shows once the cloth is on the table. Re stitch any section that pulls.
No-sew options for a quick tablecloth
A tablecloth can be made without a sewing machine when you use a fusible hem tape or a fabric glue made for cloth. These products bond the folded hem when heat or time sets the adhesive.
Fabric glue and tape hold less firmly than stitching, so test a scrap first. Follow the product directions for heat and pressing time, and let the hem set fully before use.
A pinked edge or a narrow rolled edge also keeps a casual cloth from fraying. These finishes suit a cloth that stays home and is washed gently.
Tablecloth Questions Answered
How much fabric do I need for a tablecloth?
Fabric for a tablecloth depends on the tabletop size and the drop you want, plus a hem allowance on every side. Add twice the drop to the length and to the width, then add the hem allowance to both numbers. If the fabric is narrower than the result, join two lengths along the grain.
What is the right drop length for a tablecloth?
Drop length is a choice about style rather than a fixed rule. A short drop below the edge suits everyday meals, and a longer drop that reaches near the floor reads as formal. Keep the same drop on all sides so the hem sits level.
Can I make a tablecloth without sewing?
Yes, a no-sew tablecloth is possible with fusible hem tape or fabric glue made for cloth. Fold the hem, apply the tape or glue as the product directs, and press or wait for it to set. These bonds are weaker than stitching, so test a scrap first.
How do I cut fabric straight for a tablecloth?
Cutting fabric straight starts with the grain, so pull a crosswise thread and cut along the line it leaves. Mark the finished size plus the hem allowance, then compare the diagonals to check the piece is square. Weight the corners and use sharp shears.
Which fabric works well for a tablecloth?
A fabric tablecloth works well when the cloth drapes softly and can be washed. Cotton and linen press crisply, blends resist wrinkles, and a heavier weave hides the table beneath. Check the width against your table before buying.
Should I prewash fabric before hemming a tablecloth?
Yes, prewashing and pressing the fabric before you cut prevents shrinking after the hem is sewn. Wash and dry it the way you plan to care for the finished tablecloth. Press it flat, then cut your piece to size.